Fire Alarm Systems

Buzzer for addressable detectors series 200A

FD3050 Manual Call Point – It is designed to release a signal for a Fire condition to the Fire Control Panel upon manual activation by breaking the glass on the place, signed with arrows.

The manual call point FD7150 is designed for indoor installation as a component of an Addressable Fire Alarm System IFS7000 series.The unit is compatible with the requirements of the European Standard EN54-11:2001/A1:2005, EN54-17:2005/AC:2007.

Carbon monoxide control panel of 2 zones expandable up to 3 zones. 32 detectors per zone. 2-wire installation without polarity, maximum distance of 2 km. 3 programmable level relays (extraction 1, extraction 2 and alarm). The relays can be configured for activation with a fault. Two shooting modes, standard (by value of each detector) or by the real average of the whole area. Test mode for the maintenance of the installation. Optional: TRMD-500 or TRMD-501 card allows the control of a speed controller connected to an engine achieving energy efficiency and reducing noise and vibrations. Housing made of ABS plastic, with possibility of being recessed. Dimensions: 439 x 268 x 112 mm. Power supply at 230 Vac. Certificate UNE 23300: 1984.

Standard carbon monoxide detector with electrochemical cell with deep base included. Connection to 2 wires without polarity. Diagnostic LED. Resolution: 1 ppm. Certificate UNE 23300: 1984. Dimensions: 77×100 mm. Ten years life time.

Compact carbon monoxide detector with electrochemical cell. Antivandal protection (wall fastening, shock resistance, protection against water). Connection to 2 wires without polarity. Diagnostic LED. Resolution: 1 ppm. Certificate UNE 23300: 1984. Dimensions: 93 x 93 x 55 mm. Ten years life time.

The fire detector provides reliable warning of a Fire condition responding to fixed threshold smoke concentration or rate of rise or the temperature or fixed temperature threshold detected in the protected premises.

The fire detector provides reliable early warning of a Fire condition responding to fixed threshold smoke concentration or rate of rise of the temperature or fixed temperature threshold detected in the protected premises.

DB 8000 – Standard Base – Common base, applicable for the standard fire alarm installations. DB 8000D – Base with schottky diode – Further improvement of the operation reliability through the built-in diode for removed fire detector application. DB 8000R – Base with relay output – trigger base with built-in relay output, applicable for burglar fire alarm systems, etc. DB 8000DR – Base with schottky diode & resistor – Combined current threshold base and build-in Diode base for reliability improvement and compatibility.

Standard base with addressable detectors to be used upon operation with fire control panels where wrong condition deleted detector shall be signalled as a wrong condition interruption.

DB 8000 – Standard Base – Common base, applicable for the standard fire alarm installations. DB 8000D – Base with schottky diode – Further improvement of the operation reliability through the built-in diode for removed fire detector application. DB 8000R – Base with relay output – Тrigger base with built-in relay output, applicable for burglar fire alarm systems, etc. DB 8000DR – Base with schottky diode & resistor – Combined current threshold base and build-in Diode base for reliability improvement and compatibility.

Addressable sounder base. 200A series detector compatible. CPR Certified EN54-3. Acoustic power: 80dB. Indoor use. IP21C. Dimensions: 150 x 100 mm.

Connection base for 200 and 200A series detectors. It has an anti-theft detector system. Stainless steel contacts. White color. Dimensions: 5 x 100 mm.

Deep connection base for 200 and 200A series detectors. It has an anti-theft detector system. Stainless steel contacts. Ceiling mounted with conduit entris for standars 20mm conduit. White color. Dimensions: 43 x 100 mm.

Connection base with relay output for 200 series detectors. Detector anti-theft system available. Stainless steel contacts. White color. Dimensions: 5 x 100 mm.

Conventional heat detector (fixed temperature 78ºC). Led status indicator and output for remote pilot indicator PAD-10. White color. Allows installation without polarity. Requires connection base Z-200 or Z-200-H. Anti-theft system (only with Z-200). CPR certificate EN 54-5. Dimensions: 100 x 40 mm.

Green resettable alarm button for emergencies, surface mounting. Indoor use. Dimensions 98x98x48mm.

Conventional manual call point, with test key, for surface installation. Suitable for indoor. Red color. Includes resistance of 100 Ohm.-2W. Dimensions: 98 x 98 x 48 mm. CPR certificate EN54-11.

Conventional optical and heat detector. Led status indicator and output for remote pilot indicator PAD-10. White color. Allows installation without polarity. Requires connection base Z-200 or Z-200-H. Anti-theft system (only with Z-200). CPR certificate EN 54-5 and EN 54-7. Dimensions: 100 x 40 mm.

Indoor alarm sounder with beacon. 32 selectable tones. Power at 24Vdc / 8mA at 36mA according to tone. IP33C. Red color. Acoustic power 78 to 116 dB according to tone. CPR certificate EN54-3. Dimensions: 100 x 75 mm.